Language selection

Rail transportation safety recommendation R10-01

Assessment of the Response to Rail Safety Recommendation R10–01 – R09W0016

 Recommendation R10-01 in PDF [131 KB]

Tank car stub sill failures

Background

On 14 January 2009, at approximately 0330 Central Standard Time, Canadian National freight train M-30451-11 was proceeding eastward at 4 mph when it experienced an undesired emergency brake application and came to a stop at Mile 238.30 of the Redditt Subdivision near Dugald, Manitoba. Subsequent inspection revealed that the train had separated and the A-end stub sill of dangerous goods tank car UTLX 37605, loaded with approximately 51 500 pounds of propylene (UN 1075), had severed and pulled out of the car. There was no release of product, no derailment, no track damage and no injuries.

The Association of American Railroads (AAR) requires railways to complete and submit standard reports for various mechanical component failures, including axles (MD-12), wheels (MD-115), roller bearings (MD-11), truck sides and bolsters. These reports are regularly evaluated by the AAR. In some cases, the evaluation has resulted in the issuance of AAR circulars for the recall or monitoring of potentially defective components.

With regards to tank car stub sills, car owners ensure that a SS3 Form is completed for each tank car stub sill inspection. Similarly, an R-2 Form is completed for repairs to tank car stub sills resulting from non-accidental buckles, corrosion, and cracks. While these reports are submitted to the AAR, they are not reviewed to identify emerging trends in stub sill failures. Furthermore, older tank cars are often scrapped after a stub sill failure (that is, badly cracked or broken stub sill) due to the associated cost of repair. In these circumstances, no R-2 Form is completed because the stub sill is not repaired. Consequently, information on stub sill failures is not always consistently recorded, nor is it analyzed for safety defects.

Within the North American tank car fleet of approximately 325 000 cars, about 41 000 of these (13 per cent) are equipped with UTLZBN stub sills. Approximately 35 000 of the tank cars equipped with UTLZBN stub sills are in dangerous goods service. In Canada, between January 2004 and June 2009, 58 tank cars were bad ordered for cracked stub sills (50) or broken stub sills (8). Although tank cars equipped with UTLZBN design stub sills only represent 13 per cent of the tank car population, for the 5.5-year period starting January 2004, these tank cars accounted for 34 per cent of the cracked stub sills (17 of 50) and 100 per cent of the broken stub sills (8 of 8). In many of these cases, Transport Canada (TC) had no information, or limited information, regarding these failures because there is no requirement to report them.

Unlike axles and wheels, there is no requirement for a railway to report a cracked or broken tank car stub sill to the AAR. In Canada, there is no regulatory requirement to report such failures under the Railway Freight Car Inspection and Safety Rules or, for tank cars carrying dangerous goods, under the Transportation of Dangerous Goods Act. Due to this situation, inconsistent reporting of stub sill failures has occurred, likely resulting in the under-representation of these failures. Without an industry or regulatory protocol to document tank car stub sill failures, a stub sill design that is susceptible to failure may not be identified in a timely manner. Therefore, the Board recommends that:

The Department of Transport, in conjunction with the railway industry and other North American regulators, establish a protocol for reporting and analyzing tank car stub sill failures so that unsafe cars are repaired or removed from service.
Transportation Safety Recommendation R10-01

TC’s response to R10-01 (December 2010)

Transport Canada (TC) accepts the intent of the recommendation R10-01. TC recognizes the importance of having appropriate data through effective reporting systems to protect public safety in the transport of dangerous goods.

Following this accident, TC has analyzed the current data on tank car stub sill failures to identify trends and anomalies, and will continue this work as more information becomes available. In January 2010, TC initiated an inspection program with its federal inspectors to conduct inspections of stub sills on rail tank cars.

While a North America system exists for tracking stub sill repairs, TC is committed to working with the industry and other North America regulators to take appropriate steps to improve data collection and reporting requirements. TC has ongoing meetings with the Federal Railroad Administration (FRA) and the American Association of Railroads to investigate both the particulars of this accident and the associated data collection concerns. As a consequence, TC and the FRA are considering implementing additional interim reporting requirements for industry.

Over the next 3-4 years, TC will be conducting a full review and update of reporting requirements in Part 8 of the Transportation of Dangerous Goods Regulations. This review will consider any interim measures adopted, and assess the need for further regulatory changes to improve reporting of stub sill failures.

Additional TC response to R10-01 (February 2011)

In order to specifically address recommendations (R10–01), senior representatives from Transport Canada, Transportation of Dangerous Goods Directorate and the US Federal Railroad Administration (FRA) co-chaired a meeting with key senior officials from the Association of American Railroads (AAR) and the Railway Supply Institute (RSI) in Washington on 17 December 2010. The following is a summary of actions taken based on discussions from this meeting:

TDG and Rail Safety inspectors were asked to pay close attention to the tank car of the type identified in the TSB report during their normal inspection work. A list of the affected tank car reporting marks and numbers was made available to them as well as a guideline to help identify and document stub sill defects consistent with the concerns outlined by the report. TC will also continue to work in close cooperation with FRA and Union Tank Car Company to analyze the stub sill design and the implementation of appropriate repair and modification procedures.

Board assessment of response to R10-01 (February 2011)

Transport Canada, in conjunction with the railway industry and other North American regulators are working to establish requirements for the reporting and analyzing of tank car stub sill failures. A number of initiatives are under way that will likely lead to resolving the deficiency, therefore, the Board assesses the response to this recommendation as Satisfactory Intent.

Additional TC response to R10-01 (October 2011)

The requirement for mandatory reporting of stub sill failures is currently under review with the Railway Association of Canada as part of ongoing discussions to revise the Railway Freight Car Inspection and Safety Rules. The new TCID database is expected to be implemented during 2012.

Board assessment of response to R10-01 (February 2012)

TC and the RAC are working to revise the Railway Freight Car Inspection and Safety Rules to create a mandatory protocol for reporting tank car stub sill failures so that unsafe cars are repaired or removed from service. However, for the present, the action has not been sufficiently advanced to reduce the risks of the deficiency. Therefore, the Board assesses the response to Recommendation R10-01 to remain Satisfactory Intent.

Additional TC response to R10-01 (January 2013)

Damage to a stub sill attachment with a crack greater than 6 inches is a new safety defect under the new Railway Freight Car Inspection and Safety Rules (RFCSR) approved in December 2012. The new RFCSR come into effect in February 2013.

A tank car inspection database (TCID) has been developed. The TCID will be the repository of maintenance, repairs and reported damage on stub sills. Some fine tuning for the report batching is being finalized.

Board assessment of response to R10-01 (07 March 2013)

The Railway Freight Car Inspection and Safety Rules mandate the reporting of tank car stub sill damage to ensure that unsafe cars are repaired or removed from service. With a system in place to track the defects and repairs, the risk of tank cars with stub sill failures not being repaired or removed from service has been substantially reduced. Therefore, the Board assesses the response to Recommendation R10-01 to be Fully Satisfactory.

Next TSB action

This deficiency file is assigned a Closed status.